Skip to Content

How do you remove a keg from a poppet?

Removing a keg from a poppet is relatively straightforward. The first step is to release whatever type of pressure or suction is holding the keg in place. If a gas such as carbon dioxide is being used, then the regulator should be turned off and the gas line disconnected.

If a vacuum is being used, such as with a racking system, then the vacuum source should be turned off and the vacuum line disconnected.

The next step is to uncover the poppet. This may require a hex wrench to undo some screws or bolts depending on the design of the poppet. Once it has been unscrewed, the poppet lid should be opened and the poppet itself should be removed.

Be careful when handling poppets as they can be fragile.

Now it is ready to remove the keg. Make sure to disconnect the keg’s gas in and beer out lines before attempting to lift the keg. Using two hands, grip the keg around the middle and lift it straight up.

Depending on the poppet design, it may be necessary to tilt the keg slightly to clear the poppet and obstructions around the poppet. After the keg is removed from the poppet, the lid can be put back on and the poppet returned to its original position.

What is the difference between PIN lock and ball lock kegs?

The main difference between a PIN lock keg and a ball lock keg is the type of connections used to attach them to other equipment. PIN lock kegs feature a series of three round pins, known as a TRI-clamp, on their sides.

These pins are then connected to corresponding male posts on connecting pieces of equipment, such as a CO2 regulator. Alternatively, ball lock kegs feature two protruding opening and closing mechanisms – a larger one at the top and a smaller one at the bottom – which both attach to corresponding female posts.

PIN lock kegs have become less popular in recent years, mainly due to the inherent risk of the connections failing and causing a leak. The TRI-clamp connections on PIN lock kegs always need to be kept very tight, while ball locks do not require any tightening and only need to be pushed in place.

Ball locks also offer a more secure seal so there is less risk of experiencing a leak.

Despite the relative ease of use, the ball lock mechanism is more expensive than the PIN lock mechanism and is generally not found in commercial kegs. PIN lock kegs are quite common, however, and are usually cheaper than ball lock kegs.

How do you replace a corny keg post?

Replacing a corny keg post is a fairly simple process, but it will require some special tools and supplies. First, you will need a keg post wrench or spanner. This is a special tool made specifically for removing and replacing corny keg posts.

You will also need a new corny keg post seal and some food-grade lubricant. Begin by removing the original corny keg post by unscrewing it with your keg post wrench. Make sure you have a good grip on the post so you don’t damage it.

Once the old post is off, clean the interior threading of the post and the body of the keg using a food-grade cleaner and warm water. Apply a small amount of the food-grade lubricant to the new corny keg post that you will be using.

Insert the new post into the keg and tighten with the keg post wrench. Make sure the post is not over-tightened to prevent any damage. Finally, press the new post seal onto the post to help ensure a leak-free connection.

Can pin lock keg be converted to ball lock?

Yes, it is possible to convert a pin lock keg to a ball lock keg. The process requires the replacement of both the posts (the component that is connected to the keg lid and the component that connects to the lid), the retainer ring and the associated O-rings.

The replacement parts necessary for the conversion process can be purchased from most home brewing supply stores. To perform the conversion, the user must follow a careful step-by-step procedure, which includes removing the old posts, replacing them with the new posts, attaching the retainer rings and tightening the posts securely.

After all of the new components have been installed, the O-rings should then be lubricated and attached securely around the posts. Once all of the components have been replaced, the keg should be pressurized to check for any leaks and then filled with beer as normal.

How do you fix a leaking keg?

A broken or leaking keg is one of the most frustrating things that can happen when serving beer. While a quick fix might be to simply replace the keg, this is not always the most cost-effective solution.

Below are a few tips on how to fix a leaking keg.

– Check the keg for dents or dings. Even a small dent can cause the keg to leak. If you find a dent, use a rubber mallet to gently tap it out.

– Inspect the keg coupler for cracks or breaks. The coupler is the part of the keg that connects to the taps. If it is damaged, it will need to be replaced.

– Make sure the O-ring on the keg is in good condition. The O-ring is a small rubber ring that seals the connection between the keg and the coupler. If it is cracked or damaged, it will need to be replaced.

– Check the keg for scratches or nicks. Even a small scratch can cause the keg to leak. If you find a scratch, use a sharp knife to slightly widen it. This will allow the O-ring to make a better seal.

If you have followed all of the above steps and the keg is still leaking, it is likely that the keg is damaged beyond repair and will need to be replaced.

What size are corny keg posts?

Corny kegs – also known as Cornelius kegs – are an industry standard for homebrewing beer. The posts of your typical corny keg are 11/16″-18 for the gas side, and 5/8″-18 for the liquid side. Each post on a keg has both an in and an out port, so you’ll need a gas connection and a liquid connection on each post.

The gas side usually requires a threaded fitting that screws into the 11/16″-18 post, while the liquid side usually requires a 5/8″ barb that slides into the post. This fitting is necessary in order to operate your keg; without it, you won’t be able to carbonate or dispense any beer.

How do you disassemble a Cornelius keg?

Cornelius kegs are also known as “corny kegs” and they are a popular type of container for homebrewed beer. To disassemble a Cornelius keg, you will need a few things. First, you will need a cornelius keg Disassembly & Reassembly (D&R) kit.

These kits can be purchased online or at a homebrewing supply store. The kit will include a keg spear, a O-ring kit, a rubber mallet, and a stainless steel brush.

To begin, remove the lid from the keg by depressing the ring tab and turning it counterclockwise. Once the lid is removed, inspect the rubber O-ring that forms a seal between the lid and the keg. If the O-ring is damaged, it will need to be replaced.

Next, use the keg spear to depress the pressure relief valve on the top of the keg. This will release any pressure that is inside the keg. Once the pressure has been released, use the mallet to tap on the bottom of the keg until the keg detached from the base.

Once the keg is detached from the base, you can begin to disassemble it. The keg is made up of four parts: the body, the lid, the dip tube, and the pressure relief valve. To remove the dip tube, start by unscrewing the retaining nut that holds it in place.

Once the retaining nut is removed, the dip tube can be pulled out.

To remove the pressure relief valve, start by unscrewing the cap that covers it. Once the cap is removed, the spring and poppet can be pulled out. To remove the lid, start by unscrewing the ring that holds it in place.

Once the ring is removed, the lid can be lifted off.

To reassemble the keg, start by attaching the lid to the body. Screw the ring back into place to hold the lid in place. Next, insert the pressure relief valve into the lid and screw the cap back on.

Now,insert the dip tube into the body of the keg. Make sure that the dip tube is inserted all the way and that the O-ring is in place. Screw the retaining nut back on to hold the dip tube in place.

Finally, attach the base of the keg to the body. Make sure that the O-ring is in place and screw the ring back into place to hold the base in place. Your Cornelius keg is now assembled and ready to be used.

What thread is a ball lock keg?

There is a large variety of kegs on the market, each with its own specific purpose. Ball lock kegs are a popular type of keg among homebrewers, as they are easy to use and maintain. The ball lock keg has two posts on the top, each with a different purpose.

The post on the left is the inlet, where beer is transferred into the keg. The post on the right is the outlet, where beer is dispensed from the keg. Both posts are equipped with a valve that is opened and closed by rotating a handle.

To fill the keg, the inlet valve is opened and beer is transferred into the keg. To dispense beer from the keg, the outlet valve is opened and beer is drawn out through a beer line. Ball lock kegs are easy to use and maintain, making them a popular choice among homebrewers.

Are ball lock and pin lock posts interchangeable?

No, ball lock and pin lock posts are not interchangeable. Ball lock posts are designed for one type of disconnect and pin lock posts are designed for another. The two types of connect/disconnect systems have different barbs, so the ball lock posts wouldn’t fit the pin locks and vice-versa.

Ball lock posts typically have a round opening that is slightly thicker than a pin lock post, while the pin lock post has a slot-shaped opening. Additionally, the ball lock posts uses a spring lever to secure their connection to their barb, while the pin lock posts uses a plastic ring to create a tight seal.

Therefore, ball lock posts and pin lock posts are not interchangeable.

Can you convert a pin lock keg to Ball Lock?

Yes, you can convert a pin lock keg to a ball lock keg. The process requires you to first drain the existing pin lock keg. You then need to disconnect the gas and liquid valves, the dip tubes, the lid and other fittings attached to the keg and remove them.

Next, you need to purchase a new lid and Ball Lock valves, a set of connecting posts and new dip tubes. After that, you can attach the new dip tubes, valves, posts and lid onto the keg, followed by reassembling the liquid and gas lines.

Once the keg is in the correct configuration and all the parts are properly attached, you can fill the keg with desired lager or beer and start using it for dispensing.

How do I know if my ball lock is pin locked?

The easiest way to determine if your ball lock is pin locked is by looking at the locking mechanism on the ball. If the ball has a spring-loaded pin sticking out the front, the lock is pin locked. The pin should be able to move up and down slightly when the handle is pushed.

Moreover, the most secure types of pin locks are those with a double-locking system that is designed to prevent the cylinder from rotating, even if a key is inserted. This type of pin lock will also likely require two keys to be inserted at once in order to gain access.

You may also be able to identify a pin locked ball lock visually, since the shackle is usually visible from the outside. If it appears to have a two-pronged design, it is likely pin locked.

What are the two types of kegs?

There are two main types of kegs: Sankey and party kegs. Sankey kegs are the most common type of keg used in bars and restaurants and are also often used in home brewing. These kegs are designed to be tapped using a Sankey tap, which requires a special coupler.

These kegs typically come in a variety of sizes, ranging from ½ barrels (15.5 gallons) to mini kegs (5 liters).

Party kegs, on the other hand, are designed for smaller, more casual gatherings such as house parties and picnics. These kegs typically range from 2.5 gallons up to 5 gallons. They are typically made of plastic and can be purchased with a built-in tap or a traditional tap.

Party kegs are easy to fill and transport and are also an affordable brewing option.

What is a keg?

A keg is a cylindrical container typically made of aluminum, stainless steel, or wood, and is used to store, transport, and serve beer. The shape of a keg makes it easy to stack and store in a fridge or cooler.

A keg is usually pressurized with carbon dioxide or nitrogen, and the beer is dispensed through a tap, spout, or valve. Kegs come in a variety of sizes, such as the traditional full keg that typically holds 15.

5 gallons or a half keg that contains 7.75 gallons. Depending on the type of beer, a keg will typically yield between 165 and 165 16-ounce servings. Kegs are great for events such as parties and barbecues, as they keep the beer cold for an extended period of time.

They are also worth the investment for those who are looking for the tastiest and freshest beer possible.

What type of beer is in kegs?

Kegs can contain a variety of beers, from lagers and ales to stouts and porters. Examples of popular beer styles that come in kegs include American Pale Ale, India Pale Ale, Pilsner, and Wheat beer. Additionally, craft beers like IPAs and imperial stouts can be found in kegs.

Depending on the size, kegs can range from 5 gallons (roughly 41 pints) to 15.5 gallons (roughly 124 pints). The vast majority of beers come in standard-sized kegs, which are slightly more than 5 gallons.

Generally, the type of beer available in a keg will depend on the brewery and the region, so you may have to search around to find the type of beer you desire.

How many kegs are in a barrel?

A barrel of beer traditionally consists of around half a dozen kegs, although the exact number may vary depending on the size of the kegs being used and the specific requirements of the brewery. A standard-sized keg contains around 15 gallons of beer, so a full barrel would generally contain between 90 and 96 gallons of beer (or 6 to 6.5 kegs).

A half barrel would consist of 3 to 3.5 kegs, while a quarter barrel (or “pony” keg) usually contains around 1.5 kegs.