To determine if your ball lock is pin locked, you will need to inspect the cylinder closely. The pin lock is placed inside the cylinder, just above the cylinder’s keyhole. It is typically relatively small and can be removed with a flat head screwdriver.
Once the pin lock is removed, you will be able to see if the ball lock is locked or not. If the ball lock is locked, the cylinder will be flush and there will be no gap between the two halves of the cylinder.
If the ball lock is unlocked, there will be a small gap between the two halves of the cylinder, and the pin lock will be clearly visible. Also, you can test the pin lock by inserting the key into the lock and turning it.
If the lock is unlocked, the key should be able to turn freely, but if the lock is locked, it will not turn.
Are ball lock and pin lock posts interchangeable?
No, ball lock and pin lock posts are not interchangeable. Ball lock posts use a pin as the connector, while pin lock posts use a ball as the connector. Furthermore, ball lock posts are designed for fuel lines and are secure enough to support a full keg pressure, while pin lock posts are designed for soda lines and are generally not strong enough to support a full keg pressure.
In terms of design, ball lock posts are typically longer than pin lock posts and they also tend to have a smaller opening to connect the gas line. Additionally, ball lock and pin lock posts have different threading designs and therefore cannot be connected to the same keg.
As a result, ball lock and pin lock posts are not interchangeable.
How do you use a PIN lock keg?
You need to first get a hold of a PIN lock keg. You can find these kegs at your local brewing or home brewing store. Once you have your PIN lock keg, you need to find a way to open it. But the most common way is to use a keg opener.
Once you have the keg opener, you need to find the right size for your keg. Once you have the right size, you need to find the right place to put it on the keg. The most common places to put it are on the side or on the top.
Once you have the keg opener in the right place, you need to find the right place to put your hand. The most common place to put your hand is on the top of the keg. Once you have your hand in the right place, you need to find the right place to put your foot.
The most common place to put your foot is on the bottom of the keg. Once you have your foot in the right place, you need to find the right place to put your body. The most common place to put your body is behind the keg.
Once you have your body in the right place, you need to find the right place to put your weight. The most common place to put your weight is on the top of the keg. Once you have your weight in the right place, you need to find the right place to put your beer.
The most common place to put your beer is in the middle of the keg. Once you have your beer in the right place, you need to find the right place to put your glass. The most common place to put your glass is in front of the keg.
Once you have your glass in the right place, you need to find the right place to put your mouth. The most common place to put your mouth is on the top of the glass.
What is the difference between a ball lock and a pin lock keg?
A ball lock keg uses a curved top, with two poppets that are pushed in when the lid is tightened, to create an airtight seal. This type of keg most commonly holds a capacity of 5 gallons. The poppets and release valves are spring loaded, and will depress when the dip tube and fittings are connected to the keg, allowing for flow of the liquid out and CO2 in.
A pin lock keg uses two pins for latching; these pins protrude from the top and latch into receptacles in the keg lid. Similarly to the ball lock keg, two poppets are pushed in when the lid is closed, creating an airtight seal.
This type of keg also holds a capacity of 5 gallons, but the poppets and release valves work differently. The poppets are not spring-loaded, but must be depressed manually to allow the liquid out and the CO2 in.
How long after Kegging can you drink?
Once you have finished the process of kegging your beer and allowing it to carbonate, you can enjoy it after any desired period of time. This can range from a few hours to a couple of weeks. If you wait the recommended amount of time, which is 1-2 weeks, you will allow your beer to carbonate and reach its fullest flavor potential.
The longer you wait, the more flavor and carbonation you will get out of your beer. So, it all depends on how long you’re willing to wait to have the best tasting beer. Many people choose to wait until the time recommended as it can really make a huge difference in the taste of the beer and enhance the overall experience.
How do you clean a ball lock that is disconnected?
If you’d like to clean a disconnected ball lock, it’s a fairly straightforward process that involves a few steps.
First, you’ll want to sanitize the outside of the ball lock to remove any visible dirt or grime. You can achieve this by wiping down the outside of the ball lock with a damp cloth or sanitizing wipe.
Next, you’ll want to clean the inside of the ball lock. To do this, you’ll need to fill the ball lock with a sanitizing solution. Common sanitizing solutions such as iodophor or Star San work well. After you’ve filled the ball lock, put the end with the ball lock onto a tube or hose and allow the solution to flow through the ball lock and out the other end.
This should help to clean the inside of the ball lock.
Finally, you can further sanitize the outside of the ball lock by spraying it with a sanitizing solution. Make sure to cover the ball lock completely and let it sit for around 15-20 minutes before wiping it down.
Once all of this is complete, your ball lock should be clean and sanitized.
Can beer ferment in keg?
Yes, beer can ferment in a keg. During the fermentation process, the yeast in the beer will consume the sugar in the malt and turn it into alcohol and carbon dioxide. This process can take place in a keg, as the sealed environment provides a safe and stable atmosphere where the yeast can properly convert the sugar into alcohol.
After fermentation, the beer is ready to be served. However, one should be aware that the keg does put a limit on the amount of beer that can be fermented in it due to its size, meaning larger batches of beer may require additional kegs or vessels.
For best results, the keg should be cleaned and sanitized prior to being used and left to sit in an area where temperatures will remain fairly consistent throughout the fermentation process. Lastly, ensuring adequate ventilation is key as the build up of the carbon dioxide produced during fermentation can cause the keg to burst.
How do you remove a spear from a Sanke keg?
Removing a spear from a Sanke keg can be tricky, but by following these steps it can be done safely and correctly.
1. Start by draining the keg. Make sure to disconnect the beer or gas line first, and then open the corresponding bung hole. Allow the liquid to completely drain out of the keg.
2. Once the keg is empty, turn it upside down and place it on a flat surface. This will allow you to have better access to the spear.
3. Find the retaining ring that is holding the spear in by rotating the keg. This is typically located at the top of the keg, near the cylinder base.
4. Use a flathead screwdriver to get underneath the retaining ring and pry it upward.
5. Once the retaining ring pops off, the spear should be loose. Pull the spear out of the cylinder base by pressing down on the handle and sliding it outward.
6. To replace the spear, simply insert the handle into the cylinder base and push it in until the retaining ring pops back into place. Make sure the spear is seated properly and the retaining ring is firmly in place.
That’s it! With these easy steps, you can safely and easily remove and replace the spear in your Sanke keg.
Can pin lock keg be converted to ball lock?
Yes, it is possible to convert a pin lock keg to a ball lock. This is usually done by replacing the pin lock posts and lids with ball lock posts and lids. Depending on the type of pin lock keg you have, the conversion process can be more involved than simply exchanging the posts and lids.
The cheapest and easiest way to do a conversion is to remove the old pin lock fittings and replace them with new ball lock fittings. However, if you are looking for a more rigorous approach to the conversion, you may need to re-thread the spear and collar that run through the pin lock keg.
This process will require a special drill bit and tap set to cut the threads that house the new ball lock posts and lids. While this process may require more time, patience, and know-how, it will ultimately create a more secure seal between the keg and the lid.
What is a Sanke keg?
A Sanke keg is a type of keg commonly used in the beer, wine and spirits industries. It is a cylindrical stainless steel container with two valves – one at the top and one at the bottom. The top valve usually has a large metal handle attached while the bottom valve is typically some type of connector that can be used to connect the keg to a keg tap system or a beverage dispenser.
The shape of Sanke kegs is based on their historic use as shipping vessels and their modern adaptation for beverage service. The top valve is used to secure the lid during shipping and the bottom valve for draining the liquid out of the keg once it reaches its destination.
Sanke kegs are typically of a uniform size and shape and are used by many breweries, wineries and other beverage companies to transport, store and dispense craft and draft beer, wine, ciders and other spirits.
What is Amcyl keg?
An Amcyl keg, also known as an American barrel, is a type of beer keg that is commonly used in the United States and Canada. It is a cylindrical container with a capacity of 15.5 US gallons (59.2 liters).
The keg is usually made of stainless steel, but may also be constructed from plastic or aluminum. The Amcyl keg is widely used by breweries and larger pubs, as it provides a quick and efficient way of storing and serving beer.
Its cylindrical shape allows for efficient stacking and storing, while the barrel-style construction ensures maximum strength and makes it easy to move and maneuver. The Amcyl keg has a built-in valve for venting and siphoning, and it is equipped with rubber seals to ensure a tight fit and prevent beer from leaking.
What type of kegs are there?
Kegs come in a wide variety of shapes and sizes. Generally, the most common type of keg is a Sankey D System, also known as a U. S. 1/2 barrel or Full-Size Keg. These kegs hold 15.5 gallons, or 1,984 ounces, of beer, and are 13.
2 inches in diameter and 23.3 inches in height.
Another popular keg is the European Barrel. Also known as the U. S. 1/4 barrel, these are commonly used to store and serve smaller volumes of beer. These kegs hold 7.75 gallons, or 1,008 ounces, of beer and measure 11.
2 inches in diameter and 23.3 inches in height.
Another popular keg is the Sixth Barrel (U. S. 1/6 Barrel). These kegs are commonly used to store and serve craft beers. They hold 5.2 gallons, or 661 ounces, of beer, and measure 9.8 inches in diameter and 23.
3 inches in height.
Cornelius Kegs, or home-brew kegs, are also popular. These kegs hold 5 gallons, or 640 ounces, of beer, and are 9.9 inches in diameter and 25.4 inches in height.
Finally, there are Mini Kegs. These kegs can also be known as Bubblers, or U. S. 1/4 Thin Quarter Barrels. Mini Kegs are the smallest type of keg and hold 1.32 gallons, or 169 ounces, of beer and measure 8.
5 inches in diameter and 13.2 inches in height.
Can I convert a pin lock keg to Ball Lock?
No, you cannot convert a pin lock keg to a ball lock keg. Pin lock kegs, also called Coke kegs, have a different shape liner, lid and gas ring system than ball lock kegs. In order to connect the necessary hose fittings, the keg itself would need to be modified, whih could result in the keg no longer being pressure rated.
You can, however, purchase a ball lock keg to connect with your existing pin lock keg fittings. There are also universal fittings with dip tubes that can be used to replace both types of kegs.
How many times should you purge a keg?
Kegs should be purged at least once every two months. Regular purging dramatically reduces the amount of beer lost to oxidation, and the required frequency of purging increases with the age of the keg and the type of beer it contains.
Typically, a keg should be purged with CO2 each time it is tapped. If the keg has been tapped more than two months ago and hasn’t been purged since, it is recommended to do a deep purge. A deep purge involves emptying the contents of the keg and refilling it with CO2 to 50 psi.
This forces the remaining oxygen out of the lines. You should also regularly check the beer lines to make sure they are clean, as debris can affect the taste and clarity of the beer.
What PSI should a keg be at?
The ideal pressure for serving beer from your keg is 12 to 14 PSI, although this can vary depending on the beer style, the temperature of the beer in your keg, and the temperature of the environment you’re serving in.
For example, if you’re serving lagers or lighter styles of beer, you’ll likely want to keep your PSI closer to 12, while higher ABV beers and heavier styles suit higher PSI levels. Also, if the temperature of your taproom is lower than usual, you can raise the PSI to maintain pressure.
Similarly, if your keg is warm, you’ll want to slightly lower the PSI to keep the pressure from building too much.
Ultimately, you should experiment with different pressure levels and observe the effects to find what works for your specific setup. Keeping a journal is also helpful for tracking your results and helping yourself remember what does or does not work.
With that said, a good starting point for most circumstances is between 12-14 PSI.
What are keg sizes?
Keg sizes vary and can be as small as one gallon or can reachlarge volumes and hold over a half barrel of beer. The most common sizes are mini-kegs, which contain just over five liters of beer, or a little over a gallon and a half.
These are often found in packs of four and sold under the brand names of Heineken or Miller Lite. The next size up is a sixth barrel or “tall-quarter,” which hold just under five gallons of liquid. This is a similar size to the Heineken mini-kegs, but slightly larger and not typically sold in packs.
Next, the quarter barrel or “pony-keg” is widely used and holds about 7.75 gallons of fluid or roughly 62 pints. Following the quarter barrel is the popular half barrel or “full-keg,” which holds 15.
5 gallons of beer, or 1,984 ounces, and yields roughly 124 16-ounce pints. Lastly, the largest is a European barrel, also known as a “import-keg,” “European barrel,” or “half-barrel” and can hold up to 26.5 gallons.
Generally, these kegs have a diameter of 16.5 inches and a height of 23.3 inches.
